Are you having trouble with your Whirlpool refrigerator’s water filter? When the filter needs to be replaced, it can cause a decrease in water flow or bad-tasting water. Fortunately, resetting the filter can easily solve these problems. In this blog post, we will guide you through the steps on how to reset the filter on your Whirlpool refrigerator.

Before we dive into resetting the filter, it’s important to understand the role of the filter in your refrigerator. The filter helps to remove impurities and contaminants from the water and ice that your fridge dispenses.

Over time, the filter becomes clogged with debris, which affects its performance. That’s why it’s crucial to replace the filter every six months or sooner, depending on your usage.

Now, let’s get back to resetting the filter. The process is simple, and you don’t need any special tools or expertise to do it. However, it can differ slightly depending on the model of your Whirlpool refrigerator.

how to reset filter on whirlpool refrigerator

How To Reset Filter On Whirlpool Refrigerator – Step-by-Step Instructions

To reset the filter on a Whirlpool refrigerator, locate the water filter indicator light and press and hold it for three seconds. The light will then blink rapidly. After this, open the refrigerator door and locate the water filter located on either side of its top grille or in its ceiling.

Pull out the old cartridge from its housing and discard it properly according to local recycling regulations. Insert a new compatible replacement filter into its place making sure that it is inserted with an arrow pointing toward your refrigerator’s interior wall.

Close both doors of your fridge once you have replaced your old cartridge with a new one and press down firmly on each side until they click into place.

Step 1: Unplug the refrigerator from the power source

This step is important, as it ensures that any residual electricity in the filter system will be removed and resetting can begin.

Step 2: Locate the filter cartridge inside your fridge:

It’s usually located in either a compartment on the roof of your fridge or behind a grill at its base

replacing water filter on whirlpool refrigerator 1

Step 3: Remove the filter cartridge:

You can remove the filter cartridge by pressing down gently on one side and pulling outwards on the other side until it comes loose.

Be careful not to damage any other components while doing this.

replacing water filter on whirlpool refrigerator 2

Step 4: Insert a new filter cartridge:

After successfully removing the old filter cartridge insert a new cartridge into place. Make sure that it clicks securely into place before letting go of it completely.

replacing water filter on whirlpool refrigerator 3

You may need to use some force here; if you find yourself struggling then make sure you check all connections are secure beforehand!

Step 5: Plug your refrigerator back:

Plug the refrigerator into its power source and wait for around 20 minutes for it to restart fully with its new settings applied automatically through the resetting process initiated when inserting a new filter cartridge.

How to Turn off Replace Filter on Whirlpool Refrigerator?

When your Whirlpool refrigerator is equipped with a replaceable filter, it may be necessary to turn off the Replace Filter feature.

To do this, access the control panel of your fridge and locate the replace filter option. Once you have located it, press and hold down for three seconds to deactivate it.

This will ensure that your refrigerator does not constantly remind you when it’s time to change out the filter.

How to Reset Water Filter Light on Whirlpool Side by Side?

If you have a Whirlpool side by side refrigerator with a water filter, it’s important to know how to reset the water filter light. To do this, press and hold the “Reset” button on your fridge for 3 seconds until the indicator light turns off. This will reset the water filter and allow your refrigerator to continue running efficiently.

Be sure to replace your water filter every 6 months or when needed so that you can always get clean drinking water from your Whirlpool side by side refrigerator!

How to Reset Water Filter Light on Whirlpool Side by Side?

How to reset water filter on whirlpool refrigerator?

  1. Locate the Water Filter Status Light: Look for the water filter status light on the control panel of your refrigerator. This light is usually located on the dispenser or temperature control panel.
  2. Remove the Old Water Filter: If you haven’t done so already, you’ll need to replace the old water filter with a new one. Twist the old filter counterclockwise to remove it.
  3. Install the New Water Filter: Insert the new water filter into the slot and turn it clockwise until it locks into place. Make sure it is securely installed.
  4. Reset the Water Filter Indicator: After replacing the water filter, you typically need to reset the water filter status light. This is often done by pressing and holding a button on the control panel. Check your refrigerator’s user manual for the specific button and instructions.For many Whirlpool refrigerators, the reset procedure involves holding down the “Filter Reset” or “Reset” button for a few seconds until the indicator light changes or goes off. The button might be labeled differently depending on the model.
  5. Verify the Reset: Confirm that the water filter status light has reset. It may change color, go out, or display a new status to indicate that the filter has been replaced and the reset is complete.

What is the Function Of the Water Filter Reset Button?

Water filter reset buttons are an important part of keeping your water filtration system running properly. When the filter needs to be replaced, pushing the reset button will help remind you that it’s time for a new one.

Additionally, if you notice any changes in water pressure or taste after replacing a filter, pressing the reset button often helps to restore normal operation.

The function of filter reset button of whirlpool refrigerator

How to Reset Filter on Whirlpool Gold Series Refrigerator?

Resetting the water filter on your Whirlpool Gold Series refrigerator is a simple task that only requires a few steps.

First, locate the filter cartridge in the grille at the bottom of your fridge’s interior.

Next, turn it counterclockwise until it comes free from its housing and remove it.

To reset the filter indicator light, press and hold down both the “Light” and “Power Cool” buttons simultaneously for 3 seconds until you hear a beep sound confirming that your filter has been reset.

Finally, insert a new water filter into place by turning it clockwise until it locks securely in position.

How to Reset Water Filter Light on Frigidaire Refrigerator?

Resetting the water filter light on a Frigidaire refrigerator is easy and straightforward. To begin, locate the control panel at the top of your fridge door. Once located, press and hold both of the arrow buttons for 3 seconds until you hear a beep.

This will reset your water filter light and allow it to continue functioning properly. Be sure to replace your old filter with an appropriate replacement as needed so that your fridge can continue working optimally!

Water Filter Light Will Not Reset Whirlpool

If you own a Whirlpool water filter, you may have experienced the issue of the light not resetting after changing the filter. This can be caused by several issues and is most commonly due to an obstruction in the system or a faulty switch assembly

To fix this problem, it is best to start by checking for any blockages and then replacing any broken components if necessary.

Once these steps are complete, your Whirlpool water filter light should reset automatically when a new filter is inserted.

Order Filter Vs Replace Filter Whirlpool

The Whirlpool Order Filter and Replace Filter are two types of water filters that offer a unique solution for providing clean, healthy drinking water.

The Order Filter is designed to be used for a specific length of time depending on the amount of usage and must then be replaced.

The Replace Filter is designed to last up to six months before needing replacement, making it the ideal choice for busy households that don’t want the hassle of having to remember when it’s time to order a new filter.

Both types are made with advanced filtration technology that helps reduce contaminants such as chlorine taste and odor, lead, sediment, and other particulates from your tap water.

Whirlpool Fridge Order Filter Light

The Whirlpool fridge order filter light is designed to signal when the water filter needs to be replaced. It will usually illuminate after 6 months of use, or 200 gallons of dispensed water, whichever comes first.

Regularly replacing your refrigerator’s filter ensures that you and your family are drinking clean and safe water free from contaminants.

How to reset filter notice on whirlpool refrigerator?

To reset the filter notice on a Whirlpool refrigerator, locate the filter button on the control panel. Press and hold the button for 3 to 5 seconds until the indicator light changes or resets. This action should clear the filter status and reset the notification.

Reset Refrigerator “Replace Water Filter” Indicator Light – Whirlpool | Handy Hudsonite

How Do You Reset the Filter Light on a Whirlpool Refrigerator?

To reset the filter light on a Whirlpool refrigerator, first, locate the “RESET” button located near the water filter housing.

Once found, press and hold this button for several seconds until the indicator light turns off.

If there is no RESET button present, you may need to unplug your refrigerator from its power source and then plug it back in again to reset it.

Additionally, if your refrigerator has an electronic control panel or display screen, pressing any combination of buttons such as “Ice Type” + “Light/Lock” + “Filter Reset” should also do the trick.

How Do I Reset My Whirlpool Refrigerator After Water Filter Changes?

To reset your Whirlpool refrigerator after changing the water filter, first press and hold the “Reset” button located on the display panel. The Reset button is usually indicated by a red triangle with an arrow pointing down. You will hear a beep confirming that you have successfully reset your refrigerator.

After this step, it is important to run water through the newly installed filter for 3-5 minutes or until there are no air bubbles in the flow of water before using it again.

How Do You Reset a Refrigerator After Changing Filter?

The process of resetting a refrigerator after changing the filter will vary depending on the make and model. Generally, however, you should begin by pressing and holding down the “Filter Reset” button for 3 seconds or until it beeps to indicate that it has been reset. This will enable your fridge to recognize the new filter and adjust its cooling cycle accordingly.

Additionally, some models may require you to enter a code into the digital display in order to complete the reset process. If this is necessary for your model, consult your user manual for instructions on how to do so correctly.

How Do I Reset My Whirlpool Side by Side Refrigerator?

If you need to reset your Whirlpool side by side refrigerator, the first step is to unplug it from the wall outlet. Once it’s completely disconnected, wait five minutes before plugging it back in.

This will help reset any electrical components within the fridge and allow for a clean start-up of all systems.

If this doesn’t work, try pressing and holding down both temperature control buttons for three seconds or more until you hear a beep sound indicating that your fridge has been successfully reset.

To complete the process, access Settings through the digital display and press Reset where indicated. You should now have a fully functioning Whirlpool side-by-side refrigerator!

How to reset whirlpool refrigerator after replacing water filter?

To reset a Whirlpool refrigerator after replacing the water filter, first, locate the water filter button on the control panel inside the fridge. Press and hold the button for approximately 3 to 5 seconds until the indicator light changes or resets.

This action will typically reset the water filter status and allow the refrigerator to recognize the new filter.

After resetting, run a few cups of water through the water dispenser to flush out any air or impurities in the new filter.


In conclusion, resetting your Whirlpool refrigerator’s filter is a simple process that only takes a few minutes. All you need to do is locate the filter and use the reset button next to it. If your filter light still won’t turn off after you’ve hit the reset button, contact an appliance repair service for help.

By following these steps, you can make sure your refrigerator’s water filter is working properly so that you always have access to clean drinking water.

5/5 - (2 votes)

Leave a Reply

Your email address will not be published. Required fields are marked *